#include "asm.h"
	
/*
 * Start an Application Processor. This must be placed on a 4KB boundary
 * somewhere in the 1st MB of conventional memory (APBOOTSTRAP). However,
 * due to some shortcuts below it's restricted further to within the 1st
 * 64KB. The AP starts in real-mode, with
 *   CS selector set to the startup memory address/16;
 *   CS base set to startup memory address;
 *   CS limit set to 64KB;
 *   CPL and IP set to 0.
 *
 * mp.c causes each non-boot CPU in turn to jump to start.
 * mp.c puts the correct %esp in start-4, and the place to jump
 * to in start-8.
 *	
 */

.set PROT_MODE_CSEG,0x8		# code segment selector
.set PROT_MODE_DSEG,0x10        # data segment selector
.set CR0_PE_ON,0x1		# protected mode enable flag

.globl start
start:		.code16				# This runs in real mode
		cli				# Disable interrupts
		cld				# String operations increment

		# Set up the important data segment registers (DS, ES, SS).
		xorw	%ax,%ax			# Segment number zero
		movw	%ax,%ds			# -> Data Segment
		movw	%ax,%es			# -> Extra Segment
		movw	%ax,%ss			# -> Stack Segment

		# Set up the stack pointer, growing downward from 0x7000-8.
		movw	$start-8,%sp         	# Stack Pointer
	
#### Switch from real to protected mode	
####     The descriptors in our GDT allow all physical memory to be accessed.
####     Furthermore, the descriptors have base addresses of 0, so that the
####     segment translation is a NOP, ie. virtual addresses are identical to
####     their physical addresses.  With this setup, immediately after
####	 enabling protected mode it will still appear to this code
####	 that it is running directly on physical memory with no translation.
####	 This initial NOP-translation setup is required by the processor
####	 to ensure that the transition to protected mode occurs smoothly.
	
		lgdt	gdtdesc			# load GDT -- mandatory in protected mode
		movl	%cr0, %eax		# turn on protected mode
		orl	$CR0_PE_ON, %eax	# 
		movl	%eax, %cr0		# 
	        ### CPU magic: jump to relocation, flush prefetch queue, and reload %cs
		### Has the effect of just jmp to the next instruction, but simultaneous
		### loads CS with $PROT_MODE_CSEG.
		ljmp	$PROT_MODE_CSEG, $protcseg
	
#### we are in 32-bit protected mode (hence the .code32)
.code32
protcseg:	
		# Set up the protected-mode data segment registers
		movw	$PROT_MODE_DSEG, %ax	# Our data segment selector
		movw	%ax, %ds		# -> DS: Data Segment
		movw	%ax, %es		# -> ES: Extra Segment
		movw	%ax, %fs		# -> FS
		movw	%ax, %gs		# -> GS
		movw	%ax, %ss		# -> SS: Stack Segment

                movl    start-8, %eax
                movl    start-4, %esp
		jmp	*%eax                   
	
.p2align 2					# force 4 byte alignment
gdt:
	SEG_NULL				# null seg
	SEG(STA_X|STA_R, 0x0, 0xffffffff)	# code seg
	SEG(STA_W, 0x0, 0xffffffff)	        # data seg
	
gdtdesc:
	.word	0x17			# sizeof(gdt) - 1
	.long	gdt			# address gdt